Jump past the rail
RFL Rough Fit Lab
The menu

Six Fitting Sessions And Four Bench Jobs

Everything on this page happens in Bay 3 with the same three readings and the same four rungs, adjusted for what the club is actually asked to do. A driver never sees settled rough. A wedge sees it three times.

Full ladder sessions

Club By Club

Two rungs · 90 minutes

Driver

Tee height, strike map, head shape and shaft profile. Rungs one and two only, because the second rung here means a hard, fast tee box rather than turf. The plot still matters: a dry summer tee changes tee depth and that changes your low point.

Full detail

Four rungs · 150 minutes

Irons

The complete ladder across a long, mid and short iron, with progression checked through the set rather than assumed from a catalogue. This is the longest session and the one that changes the most scorecards.

Full detail

Three rungs · 100 minutes

Fairway woods

Off the deck first, off the tee second, and always through the bare ground rung because a fairway wood on August turf is where sole camber either works or embarrasses you.

Full detail

Three rungs · 100 minutes

Hybrids

Rungs two, three and four. The mown turf rung is a formality for a club whose whole reason for existing is the lies where a long iron stops working.

Full detail

Four rungs · 110 minutes

Wedges

Grind and effective bounce against real ground, plus a bunker block if the schedule allows. Run in both seasonal states if you book one in each half of the year.

Full detail

Indoors · 75 minutes

Putters

The one session with no plot involvement. Stroke arc, rise and fall, face rotation rate, length, lie, head mass and balance measured on the indoor surface at two green speeds.

Full detail
Bench only

Work That Does Not Need The Plot

Not every problem is a fitting problem. These are booked in shorter slots and often solve the thing you actually came in about.

30 to 45 minutes

Loft and lie correction

Measured on the machine, bent to spec, remeasured, and recorded on a card. Forged heads bend readily; cast heads get assessed first and we will refuse rather than crack a hosel.

Per club

Reshafting

Pull, clean, ream if needed, tip to the trim we agree, glue, cure, swingweight and grip. If you have a ladder card on file we work to the numbers on it rather than to a chart.

Same day

Regripping

Tape count set from hand measurement rather than from the box label, so a build-up you liked five years ago can actually be reproduced.

60 minutes, seasonal

The recheck

A short revisit of rungs one and four with your existing set, usually booked in October or March when the ground flips. Cheap, quick, and it catches drift before it costs you shots.

Choosing

If You Are Not Sure Which To Book

Symptom to session
What you noticeWhere to start
Fine off a tee, thin from the fairwayIron session, or a fairway wood session if it is the three-wood
Good on the range, poor on the courseIron session. This is the exact complaint the ladder was built for
Long irons no longer getting airborneHybrid session
Digging in winter, bouncing in summerWedge session, booked in the season that bothers you more
Distance falling off with no swing changeBag audit first. Often lie drift or a dead grip, not a new set
Pushing short puttsPutter session

If none of those describe it, call and describe it in your own words. Bao will route you to the right slot, and if the honest answer is that nothing here will help, he will say that too.

The short version

Rough Fit Lab is a two-person bench on North Blackstone with a turf plot behind it. Every candidate build gets hit off mown grass, off bare valley ground, out of a kikuyu collar, and out of settled rough before anybody writes a spec down. If a club only behaves on the first surface, it does not leave with you.

  • Turf plot behind the bay
  • No brand quota, no house line
  • Build sheet printed, not emailed

Where and when

Rough Fit Lab
6122 N Blackstone Avenue, Bay 3
Fresno, CA 93710

(559) 555-0184
[email protected]

Bench hours
MondayClosed
Tuesday7:00 AM to 3:00 PM
Wednesday7:00 AM to 3:00 PM
Thursday7:00 AM to 6:00 PM
Friday7:00 AM to 6:00 PM
Saturday6:30 AM to 1:00 PM
SundayClosed

Everything else

© 2026 Rough Fit Lab. Written and built in Fresno.

6122 N Blackstone Avenue, Bay 3 · Fresno, CA 93710 · (559) 555-0184