Jump past the rail
RFL Rough Fit Lab
Rates

Published, Because Asking Should Not Be Awkward

A fitting fee buys bay time, plot time, the fitter's attention and a printed ladder card. It does not buy components, and no component is ordered until you have seen the price written down and said yes to it.

There is no membership, no annual plan and no package that gets cheaper if you buy three. There is one discount, described further down, and it applies automatically without anybody having to ask for it.

Full ladder sessions

Bay And Plot Time

Driver

$140

90 minutes · two rungs
  • Face map from sprayed blocks
  • Soft tee and baked tee readings
  • Head, then shaft, then length
  • Printed card, both tee conditions
What happens

Irons

$220

150 minutes · four rungs
  • Full bag audit included
  • Long, mid and short iron on all four rungs
  • Progression checked through the set
  • Frequency slope plotted before build
  • Printed card with block averages
What happens

Fairway wood

$155

100 minutes · three rungs
  • Off the deck before off the tee
  • Bare ground rung always included
  • Sole camber and entry angle read
  • Printed card
What happens

Hybrid

$155

100 minutes · three rungs
  • Rungs two, three and four
  • Crossover point against your long irons
  • Head shape read on the collar
  • Printed card
What happens

Wedges

$170

110 minutes · four rungs
  • Grind and effective bounce on real ground
  • Bunker block when the schedule allows
  • Gapping checked against your carry medians
  • Printed card, both seasonal states noted
What happens

Putter

$125

75 minutes · indoors
  • Stroke arc and face rotation captured
  • Aim measured with a shaft laser
  • Two surface speeds
  • Printed card
What happens
Bench jobs

Work That Does Not Need The Plot

Bench rates, labour only
JobRateNotes
Bag audit, standalone$45Fifteen to twenty minutes. Free when it happens inside a booked session
Loft and lie, per club$9Measured, bent, remeasured, recorded. Minimum four clubs
Loft and lie, full set$70Eight or more clubs, with the before and after sheet
Regrip, per club$6Labour and tape. Grip itself is separate
Reshaft, per club$32Pull, clean, ream if needed, tip, glue, swingweight, grip
Shaft pull, preserving the shaft$18Heat controlled. We will tell you honestly if it is likely to be destructive
Length adjustment, per club$14Includes swingweight correction back to target
Full set assembly, components supplied by you$185Eight clubs, built in one run to one set of tolerances
Seasonal recheck$60Rungs one and four with your existing set, October or March
The one discount

Half The Session Fee Comes Back If You Build Here

Book a session, decide to have the winning build made at this bench, and fifty percent of the session fee is credited against the build. It happens automatically on the invoice and nobody has to negotiate for it.

The reason it exists is straightforward. A session that ends in a build has already paid for a good portion of the bay time through the assembly labour, and charging full freight for both feels like double dipping. The reason it is only half is equally straightforward: if the credit were the whole fee, the incentive to find you a reason to buy something would be uncomfortably strong.

If you take your card and buy the clubs somewhere else, that is fine and the card is yours. It carries the full specification down to tip trim and tape count, and any competent builder can work from it. We would rather you got the right clubs than that we got the sale.

When we hand the money back entirely

If the session concludes that nothing in your bag should change, you pay the bag audit rate and nothing else. This happens roughly a dozen times a year, usually to players who arrived convinced that a component was to blame for something the ground was doing.

The small print, in normal size

Deposits, Changes And Components

  • Deposit. Fifty dollars holds a bay and comes off the session fee. Refunded in full if you give us twenty four hours. Kept if you do not, because a missed slot in a one-bay shop cannot be resold on the day.
  • Components are quoted, not estimated. Before anything is ordered you get a written figure covering heads, shafts, grips, ferrules and labour. That figure does not move afterwards unless you change the specification.
  • Payment. Card or cash at the bench. Full sets are half on order and half on collection. No financing, no store account.
  • Rebuilds inside sixty days. If a build does not match the card it was written from, we fix it at no charge and we do not argue about whose fault it was.
  • Summer scheduling. June through September the outdoor portion has to run before roughly ten in the morning. That is a physical limit, not a preference, and it is why the early slots go first.

The short version

Rough Fit Lab is a two-person bench on North Blackstone with a turf plot behind it. Every candidate build gets hit off mown grass, off bare valley ground, out of a kikuyu collar, and out of settled rough before anybody writes a spec down. If a club only behaves on the first surface, it does not leave with you.

  • Turf plot behind the bay
  • No brand quota, no house line
  • Build sheet printed, not emailed

Where and when

Rough Fit Lab
6122 N Blackstone Avenue, Bay 3
Fresno, CA 93710

(559) 555-0184
[email protected]

Bench hours
MondayClosed
Tuesday7:00 AM to 3:00 PM
Wednesday7:00 AM to 3:00 PM
Thursday7:00 AM to 6:00 PM
Friday7:00 AM to 6:00 PM
Saturday6:30 AM to 1:00 PM
SundayClosed

Everything else

© 2026 Rough Fit Lab. Written and built in Fresno.

6122 N Blackstone Avenue, Bay 3 · Fresno, CA 93710 · (559) 555-0184